Raw source water contains parts of plants, blue-green algae and their toxins, and many other types of organic matter. Identifying the types and amounts of organic matter helps treatment plant operators make informed decisions about the most efficient and cost-effective methods for treating and removing unwanted substances from source waters. The problem is that many of the tests for identifying organic compounds can take hours to days to deliver results. This research developed a test that gives information immediately. It uses three commercially available fluorescent probes that each emit fluorescent light at a specific wavelength. Certain compounds within organic matter, such as proteins, “reflect” the fluorescent light, but at different wavelengths which can be detected by the probes. These patterns of “reflected” fluorescence were related to traditional tests for organic compounds. This on-line fluorescence monitoring was then trialled at real-world treatment plants. The patterns gave reliable information about broad categories of organic compounds and there was a linear correlation between dissolved organic carbon and fluorescent intensity in both raw and treated waters. This research has provided a valuable addition to the suite of tools available for producing safe, high quality drinking water.

N-nitrosodiumdimethylamine (NDMA) in drinking water is one of many factors – such as a persons’ genes – that cause cancer. Although NDMA is not a sole cause of cancer, the water industry aims to minimise its contribution to illness and disease. This research measured levels of NDMA in drinking and recycled waters and found the majority well below the Australian Drinking Water Guideline values that are considered safe for public consumption. Different sources of NDMA were identified and water monitoring and treatment strategies to optimise NDMA removal from source waters were recommended.

Reverse osmosis (RO) is used to desalinate seawater and brackish groundwater, and to remove microscopic pathogens from treated wastewater. The salty water is pressurised on one side of the RO membrane and this is part of the process that results in water molecules passing (diffusing) through the membrane to the lower pressure solution on the other side. Salts such as sodium chloride (table salt) and calcium sulphate and calcium carbonate (scale) do not diffuse easily across the RO membrane and build up on the high-pressure side. Eventually scale deposition on the membrane prevents the diffusion of water molecules and the production of freshwater declines. This research tested four commercial and three in-house antiscalent chemicals, and additionally developed a technique to monitor scale formation and RO membrane performance in real-time. It was concluded that the antiscalent ‘PC-191T’ was best and that adding an ‘Electrical Impedance Spectroscope’ to RO systems has the potential to deliver a sensitive in-situ, real-time monitoring method capable of detecting very early scale formation, well before membrane performance declines. This will enable optimisation of membrane scale removal and improve the efficiency of freshwater production.

Harmful pathogens and compounds must be removed from wastewater before it can be discharged to the environment or used for irrigation, and many source waters need salts removed to make them potable. Microfiltration and ultrafiltration membranes remove pathogens and unwanted chemicals but as they are used, they become fouled and blocked by particulates and compounds from the water being filtered, as well as by the formation of biofilm, and by chemical interactions between solutes and the membrane materials. Although the membranes are cleaned regularly, the cleaning chemicals themselves can cause a problem. This research characterised the damage that various cleaning regimens inflict on membranes made of different materials and examined the effects of progressive and consecutive stages of membrane aging and degradation on performance. It was concluded that the type of cleaning agent affects the mechanism of membrane degradation and the severity of membrane integrity loss. More information is needed regarding the cleaning protocols and agents used in industry. Information from this research can inform a generally applicable model to predict membrane aging and decline in performance.

In Australia, remote and regional communities frequently manage relatively small, isolated water treatment and waste management systems which have water quality and health risks characteristic of small-scale decentralised operations. Australian water utilities have a wealth of experience in addressing these issues, and this project gathered and documented a series of case studies from Victoria, Tasmania and the Northern Territory to form a knowledge base that can be referred to in the future.

Water treatment plant operators remove cyanobacteria and the toxins they produce from source waters but calculating the amount of treatment needed for effective removal is difficult, particularly in bloom conditions when cyanobacterial cell numbers and toxins change quickly. Current cell counting and toxin measurement can take hours or days to complete, and the results are not available quickly enough to help treatment plant operators respond to changing conditions. There is a need for a real-time method that gives instant results. This research examined the utility of fluorometers; probes that emit light that is ‘reflected’ back at different wavelengths by living cells and other matter in the water and is detected by the fluorometer. It was found that when only one species of cyanobacteria was present, there was a good correlation between the fluorescent signal and cell number, particularly when source waters were clear and not cloudy. Cell numbers did not relate well to levels of toxins or taste and odour compounds. When fluorometers were installed in 13 water treatment plants the correlation between cyanobacteria cell numbers and fluorometer signals was validated, and this led to the conclusion that fluorometers can give early warning of blue-green algae blooms.

The protection of sources of water and catchments is an important method for maintaining water quality; one that can mitigate cost and reliance on downstream water treatment and disinfection. Catchment protection requires risk assessment, but water quality management approaches were not originally developed for natural environments, and ecosystem-based methods (such as the Ecological Risk Assessment methodology), require complex data inputs often unavailable to water utilities.

This paper discusses various water quality risk management techniques and proposes a step-by-step catchment risk assessment methodology that is compatible with the Australian Drinking Water Guidelines.

Cyanobacterial blooms in surface waters are a source of cells, taste and odour compounds, and a range of toxins. This research optimised treatment processes for the removal and control of cyanobacteria and their metabolites from a range of source waters. It was concluded that pre-chlorination is not advisable when cyanobacteria are present, but that in some situation’s potassium permanganate is a viable alternative. Although all three tested coagulants; ferric chloride, aluminium chlorohydrate and aluminium sulphate (alum) removed 90 to 95% of cells, alum at pH 6.3 was the most cost-effective. Maintaining pH > 6 reduced cell lysis and metabolite release. Since cyanobacteria in sludge remained viable for 2-3 weeks it was recommended that sludge detention in the clarifiers should be minimised.

Cyanobacterial blooms are a major problem for reservoir managers because of the large numbers of cells and the toxins they contain. These blue-green algae blooms have traditionally been treated with the algaecide copper sulphate, but this was expensive and unsustainable because it killed non-target species and left residual contaminants. This research examined and rejected alternatives: other copper-based algaecides, hydrogen peroxide, substances that trap cyanobacterial-growth supporting nutrients on the floor of the reservoir, and mechanical surface mixers. Laboratory experiments that tested the ability of ultrasound to prevent the photosynthetic cyanobacteria from floating at the depth that optimises light absorption were initially promising because the ultrasound reduced photosynthesis and metabolism and the blue-green algae died. Unfortunately, when an ultrasound system was deployed in a reservoir, the much larger volume of water attenuated and ‘absorbed’ the low-power ultrasound and led to the conclusion that sustainable, environmentally friendly levels of ultrasound do not provide effective control of blue-green algae. This rigorously conducted scientific study has generated useful information about methods which do not work, and resources can now be directed to promising new innovations.

Remote and regional Australian communities commonly produce potable water by removing salt from brackish groundwater. Existing desalination technologies, such as reverse osmosis (RO) have high electrical energy and technical requirements. Groundwaters often contain high levels of silica (quartz) which, together with the salts, form scale which blocks RO membrane and other components which are expensive to replace. This research examined an alternative desalination process: capacitive deionisation. Laboratory-scale experiments found that single-walled carbon nanotubes were the best material to use for electrodes, that membranes placed before the electrodes increased efficiency of salt removal and decreased energy usage, while silica, which lacks a charge that would bind it to either the positive or negative electrode, did not form scale deposits nor interfere with the desalination process. A full-scale version of this unit was tested onsite in the Northern Territory and described in WaterRA Project 1047.